2 atc general purpose capacitors: npo (cog) dielectric electrical characteristics capacitance range: 0.5 pf to 0.10 ?. temperature characteristic: 0 30ppm/?. operating temperature range: -55? to +125?. dissipation factor: 0.1% (max.) @ + 25?, @1 mhz 1000 pf; @1 khz >1000 pf insulation resistance @ + 25? and rated vdc: 100,000 megohms (min.) or 1000 ohm-farads (min.), whichever is less. dielectric withstanding voltage: 250% of rated voltage for 5 1 seconds, 50 milliamps (max.). unless otherwise specified all test data is at + 25?. t (max.) mb l w temperature coefficient temperature (celsius) temperature (celsius) minimum ir vs. temperature impedance vs. frequency dissipation factor vs. frequency aging rate voltage coefficient of capacitance sales of atc products are subject to the terms and conditions contained in american technical ceramics corp. terms and conditio ns of sale(atc document #001-992 rev. a 10/03). copies of these terms and conditions will be provided upon request. they may also be viewed on atc's website at www.atceramics.com/produc tfinder/default.asp. click on the link for terms and conditions of sale. atc has made every effort to have this information as accurate as possible. however, no responsibility is assumed by atc for it s use, nor for any infringements of rights of third parties which may result from its use. atc reserves the right to revise the content or modify its product without prior notice. ? 1997 american technical ceramics. all rights reserved. american technical ceramics www.atceramics.com atc north america 631-622-4700 ? sales@atceramics.com atc europe +46 8 6800410 ? sales@atceramics-europe.com atc asia 86-755-8366-4318 ? sales@atceramics-asia.com
3 dimensions shown in inches (mm) higher voltages available upon request. * ir and vapor phase soldering only recommended. atc general purpose capacitors: npo (cog) dielectric part number code 0603 npo 1r 0 c t 2 a t size code packaging: t=7 reel, b=bulk *r=13 reel - *special order temperature characteristic marking: a=no mark capacitance code: first 2 significant digits for capacity. *s=eia code - *special order indicates number of zeros following digits of capacitance in picofarads r=decimal point wvdc code a 7 wvdc 10 16 * special order - consult factory 1 25 2 50 3 10 0* 4 200* 5 500* 6 1000* 8 2000* 9 5000* cap. code cap. pf 0r5 0.5 1r0 1.0 1r2 1.2 1r5 1.5 1r8 1.8 2r2 2.2 2r7 2.7 3r3 3.3 3r9 3.9 4r7 4.7 5r6 5.6 cap. code cap. pf 6r8 6.8 8r2 8.2 100 10 120 12 150 15 180 18 220 22 270 27 330 33 390 39 470 47 cap. code cap. pf 560 56 680 68 820 82 101 100 121 120 151 150 181 180 221 220 271 270 331 330 391 390 cap. code cap. pf 471 470 561 560 681 680 821 820 102 1000 122 1200 152 1500 182 1800 222 2200 272 2700 332 3300 cap. code cap. pf 392 3900 472 4700 562 5600 682 6800 822 8200 cap. code cap.f 103 .010 123 .012 153 .015 183 .018 223 .022 cap. code cap.f 273 .027 333 .033 393 .039 473 .047 563 .056 683 .068 823 .082 104 .10 124 .12 154 .15 184 .18 cap. code cap. f 224 .22 274 .27 334 .33 394 .39 474 .47 564 .56 684 .68 824 .82 105 1.0 125 1.2 155 1.5 cap. code cap. f 185 1.8 225 2.2 275 2.7 335 3.3 395 3.9 475 4.7 565 5.6 685 6.8 825 8.2 106 10.0 126 12.0 156 15.0 standard eia capacitance values reference table size length (l) width (w) tol. l & w t max. term. (mb) min. max. min. cap. max. cap. (code) & wvdc 10v 16v 25v 50v 100v 200v 500v 1000v 2000v 5000v 0402 .040 (1.02) .020 (0.51) .004 (0.10) .025 (0.64) .004 (.10) .012 (.30) 0r5 271 331 221 101 680 0504 .050 (1.27) .040 (1.02) .006 (.152) .044 (1.12) .005 (.12) .015 (.38) 0r5 182 122 102 561 391 0603 .063 (1.60) .031 (0.80) .005 (0.12) .035 (0.89) .005 (.12) .015 (.38) 0r5 102 102 102 102 271 0805 .079 (2.00) .049 (1.25) .008 (0.2) .051 (1.30) .010 (.25) .028 (.71) 0r5 103 472 332 182 122 471 331 1206 .126 (3.20) .063 (1.60) .008 (0.2) .051 (1.30) .010 (.25) .028 (.71) 0r5 153 223 103 562 392 102 821 271 1210 .126 (3.20) .098 (2.50) .008 (0.2) .067 (1.70) .010 (.25) .028 (.71) 681 273 223 223 103 822 222 182 681 1812 .177 (4.50) .126 (3.20) .010 (0.25) .067 (1.70) .010 (.25) .030 (.76) 471 393 393 333 183 123 392 222 122 2225* .220 (5.59) .250 (6.35) .015 (0.38) .070 (1.78) .010 (.25) .030 (.76) 102 104 104 104 683 473 153 103 472 capacitance tolerance code b* c g* j tol. ?.1 ?.25 ? ? pf (values < 10 pf) % (values > 10 pf) *tighter tolerances available. american technical ceramics www.atceramics.com atc north america 631-622-4700 ? sales@atceramics.com atc europe +46 8 6800410 ? sales@atceramics-europe.com atc asia 86-755-8366-4318 ? sales@atceramics-asia.com termination code t = tin plated over nickel barrier (standard), rohs compliant w = tin/lead, solder plated over nickel barrier** c = palladium silver, (non-magnetic), rohs compliant** ** consult atc for availability
|
